Skip to content
Back to guides
Machine ElementsMay 9, 2026|9 min read

Machine element life, S-N Wöhler curves, and fatigue guide

High-cycle fatigue analysis, S-N Wöhler curves, Marin modification factors, Goodman failure criterion, and Miner cumulative damage rule.

Engineering Review: Independent Mechanical Engineer & Developer
|
#fatigue#Wöhler#service life#Goodman#S-N curve#FKM#DIN 50100
Engineering Usage Note

This guide outlines the analytical fatigue verification of dynamic components such as shafts, bolted joints, welded structures, and springs in accordance with DIN 50100, FKM guidelines, and Shigley mechanical design methodology. For mission-critical aerospace and pressure vessel systems, empirical component testing remains mandatory.

Problem / Objective

Over 80% of mechanical component failures occur not from monotonic static overloads, but from progressive fatigue fracture under cyclic stresses far below the material yield strength (S_y). Relying solely on static safety factors (S_static >= 1.5) leads to:

  • Silent micro-crack initiation at stress concentrations (fillets, keyways, weld toes),
  • Sudden catastrophic brittle fracture with zero warning or macroscopic plastic deformation,
  • Costly downtime and cascading mechanical equipment destruction.

Assumptions

  • High Cycle Fatigue (HCF, N > 10^4 cycles) governs, where macroscopic bulk behavior remains within the nominal elastic regime.
  • The base fatigue limit is derived from rotating beam tests (RR Moore) and corrected via Marin surface, size, and loading factors.
  • Mean stress influence on endurance limit is evaluated using the modified Goodman or Soderberg failure criteria.
  • Variable amplitude spectrum loads follow the Palmgren-Miner linear cumulative damage hypothesis.

Step by step method

  1. Calculate Alternating and Mean Stress Components: From peak cyclical stress levels (σ_max and σ_min):

σ_a = fracσ_max - σ_min2, σ_m = fracσ_max + σ_min2

Stress ratio: R = fracσ_minσ_max (Fully reversed: R = -1; zero-to-tension: R = 0).

  1. Compute Corrected Endurance Limit (S_e) via Marin Equation: Modify laboratory endurance limit (S_e' ≈ 0.5 * S_ut) to represent actual hardware conditions:

S_e = k_a * k_b * k_c * k_d * k_e * S_e'

  • k_a: Surface finish factor (ground, machined, hot-rolled, as-forged),
  • k_b: Size modification factor (k_b ≈ 1.24 * d^-0.107 for d > 8 mm),
  • k_c: Load factor (1.0 for bending, 0.85 for axial, 0.577 for pure torsion),
  • k_e: Fatigue notch sensitivity factor (k_e = 1 / K_f).
  1. Determine Fatigue Safety Factor (n_f) Using Modified Goodman: Using ultimate tensile strength S_ut and corrected fatigue limit S_e:

(σ_a / S_e) + fracσ_mS_ut = (1 / n_f) implies n_f = frac1(σ_a / S_e) + fracσ_mS_ut

Achieving n_f >= 1.3 - 2.0 guarantees infinite life (N >= 10^6 - 10^7 cycles) under uninterrupted constant amplitude cycling.

  1. Evaluate Cumulative Damage via Miner's Rule: For multi-stage spectrum loading with applied cycles n_i at stress amplitude i having fatigue life N_i:

D = sum_i=1^k (n_i / N_i) <= 1.0

  1. Industrial Worked Example: A gearbox input shaft manufactured from quenched & tempered AISI 4140 steel (S_ut = 900 MPa, S_y = 650 MPa, Marin corrected endurance limit S_e = 360 MPa) operates under alternating bending stresses between σ_max = 220 MPa and σ_min = -80 MPa:
    • Stress amplitude: σ_a = (220 - (-80) / 2) = mathbf150 MPa
    • Mean stress: σ_m = (220 + (-80) / 2) = mathbf70 MPa
    • Modified Goodman factor of safety:

(1 / n_f) = (150 / 360) + (70 / 900) = 0.4167 + 0.0778 = 0.4945 implies n_f = mathbf2.02

  • Verdict: n_f = 2.02 > 1.50, confirming safe operation in the infinite life domain.

Common mistakes

  • Equating Static Yield Safety with Fatigue Life: A shaft with a static safety factor of 3.0 may exhibit a fatigue safety factor of 0.8 and fracture after only 50,000 cycles.
  • Specifying Sharp Fillet Radii at Steps: Increasing the fillet transition radius from r/d = 0.05 to 0.15 slashes stress concentration by nearly 50%.
  • Neglecting Surface Roughness in Severe Service: Rough-machined finishes reduce fatigue endurance limits by up to 35% compared to polished specimens.
  • Overlooking Environmental Corrosion: In corrosive environments, ferrous alloys exhibit no true fatigue limit (S_e); the S-N curve drops continuously without a horizontal plateau.

Fatigue Failure Mechanisms

Fatigue failure proceeds through three distinct stages: crack initiation, crack propagation, and final fracture. Understanding these stages determines which engineering intervention prevents failure.

Stage 1 — Initiation: Begins at a stress concentration — machined notch, corrosion pit, inclusion, or surface scratch. Even below the yield strength, cyclic loading causes local plastic slip along slip planes, forming a persistent slip band. A micro-crack nucleates at the surface or just below it. Shot peening and surface hardening are effective here: they introduce compressive residual stress at the initiation site, suppressing early crack opening.

Stage 2 — Propagation: The crack grows incrementally with each load cycle. The Paris-Erdogan law describes the growth rate:

da/dN = C * (Delta K)^m

Where:

  • da/dN = crack growth per cycle (m/cycle)
  • Delta K = stress intensity factor range = Y * Delta sigma * sqrt(pi * a) (MPa·√m)
  • C, m = material constants (for steel: C ≈ 6×10^-12, m ≈ 3)

Stage 3 — Fracture: When the remaining cross-section can no longer support peak load, sudden overload fracture occurs. On the fracture surface, beach marks (visible concentric arcs) mark each crack front position during propagation — a definitive indicator of fatigue failure in post-fracture analysis.

S-N Curve Interpretation

The S-N (Wöhler) diagram plots alternating stress amplitude vs. cycles to failure. Three regions:

  • Low cycle fatigue (LCF, N < 10^4): Plastic strains dominate; material yields per cycle. Use strain-life (epsilon-N) approach. Relevant for pressure vessels and engine components under infrequent overload.
  • High cycle fatigue (HCF, 10^4 < N < 10^7): Elastic behavior with damage accumulation. The S-N curve is valid here; design stress must remain below the curve for the required cycle count.
  • Endurance limit region (N > 10^7): For ferrous materials (steels), the S-N curve becomes horizontal — the endurance limit Se. Below Se, infinite life is theoretically achieved. Aluminum alloys do NOT have a true endurance limit — the S-N curve continues to decline, requiring a finite-life approach for all aluminum structural applications.

Endurance limit estimation (Shigley / MIL-HDBK-5): Se' ≈ 0.5 * Su for Su < 1400 MPa (steel) Se' ≈ 700 MPa for Su > 1400 MPa

These are material endurance limits. The corrected endurance limit Se = ka * kb * kc * kd * Se' applies Marin factors for surface finish (ka), size (kb), load type (kc), and temperature (kd).

Surface Treatments for Fatigue Life

Post-machining surface condition significantly alters fatigue performance:

TreatmentSurface Roughness RaFatigue Life FactorMechanism
Ground (Ra 0.4 µm)0.2–0.4 µm1.0 (baseline)Smooth surface reference
Shot Peened0.8–2.0 µm (increased)1.2–1.5×Compressive residual stress
Nitrided (gas/plasma)0.4–0.8 µm1.5–2.5×Hard case + compressive stress
Hard Chrome Plated0.3–0.8 µm0.7–0.9×Tensile residual, hydrogen embrittlement risk
Electroless Nickel0.4–0.6 µm0.85–1.0×Slightly beneficial if baked

Key insight: Grinding produces tensile residual stress in the surface if performed aggressively (burn). This reduces fatigue life below the calculated value. Always specify "no thermal damage" or verify with Barkhausen noise inspection for fatigue-critical components.

Frequently Asked Questions

What happens when a component exceeds the endurance limit for a single cycle? Nothing irreversible if the exceedance is brief and the stress stays below yield. However, the cumulative damage model (Palmgren-Miner, D = Sum of ni/Ni) accumulates damage from each cycle above the limit. If D ≥ 1.0, failure is predicted. For safety-critical parts, design to D ≤ 0.3–0.5 to account for statistical scatter.

Does aluminum have a fatigue endurance limit? No. Unlike steel, aluminum alloys show a continuously declining S-N curve with no horizontal asymptote. Design aluminum structures for a specific life (typically 10^7 or 10^8 cycles) with a defined stress level, never for "infinite life." This is critical for aircraft structures, bicycle frames, and rotating aluminum components.

How can I reduce Kf without changing geometry? Increasing the notch radius (r) reduces Kt — machine a generous fillet radius at all transitions, keyways, and shoulder steps. Additionally, shot peening the notch region reduces effective Kf by introducing compressive residual stress. Specifying a lower surface roughness at the notch (Ra < 0.8 µm) further reduces the surface factor ka, improving the corrected endurance limit Se.

  • DIN 50100: Testing of Materials - Continuous Vibration Fatigue Testing (Wöhler Test).
  • FKM Guideline: Analytical Strength Assessment of Mechanical Components (VDI).
  • ISO 1099: Metallic Materials - Fatigue Testing - Axial-Force-Controlled Method.
  • Eurocode 3 (EN 1993-1-9): Fatigue Assessment of Steel Structures.

Related engineering links

Calculators, terms, and companion guides that share the same engineering concepts.

Related calculators

Bolt Size & Torque

FreeMechanical

Calculate stress area and preload from nominal diameter, pitch, and grade.

Tensile Stress

FreeMechanical

Compute tensile stress from force and cross-section area.

Bending & Deflection

FreeMechanical

Bending stress and max deflection for a simply supported beam.

Bolt Data Center

FreeMechanical

Quick access to metric and imperial bolt sizes.

Guides

Welded design safety and cost balance

Manufacturing

Engineering evaluation of load path, inspection methods, distortion, and cost when choosing fillet or full-penetration welds. AWS D1.1 and EN 1993 referenced.

Helical Compression Spring Design and Force-Deflection Guide: EN 13906-1

Machine Elements

Comprehensive engineering guide on helical compression spring rate k, deflection, Wahl stress correction, solid length, and fatigue limits under EN 13906-1.

Key design 101: parallel keys and mechanical wedges

Machine Elements

DIN 6885 shaft-hub parallel keys, shear and bearing crushing stress verification, wedge mechanics, and self-locking conditions.