Bearing Life (L10)
Calculate L10 and L10h from C, P, type, and rpm.
Find required fillet size from load, weld length, and allowable stress.
Calculate required leg size (a) based on applied load, weld length, and allowable stress.
Required leg size, throat thickness, and stress verification.
Required leg size a
1.26 mm
Throat thickness
0.89 mm
Stress verification
-
-
Formulas used
sigma = F / (0.707 * a * L)
a_req = F / (0.707 * L * sigma_izin)
Variables
Usage notes
After checking the basic result, open sharing, PDF, method notes, and comparison panels.
Similar calculators
Explore calculators with similar categories or tags.
Calculate L10 and L10h from C, P, type, and rpm.
Calculate open belt length, small pulley wrap angle, and tension allowance checks from pulley diameters and center distance.
Analyze linear tolerance stacks with worst-case, RSS, and sensitivity contribution views.
Bending stress and max deflection for a simply supported beam.
Doc version: 1.1.0 | Updated: 2026-10-16
Calculate required leg size (a) based on applied load, weld length, and allowable stress.
Required leg size, throat thickness, and stress verification.
Required leg size a
1.26 mm
Throat thickness
0.89 mm
Stress verification
-
-
Formulas used
sigma = F / (0.707 * a * L)
a_req = F / (0.707 * L * sigma_izin)
Variables
Usage notes
After checking the basic result, open sharing, PDF, method notes, and comparison panels.
In a standard 90-degree T-joint or lap joint, an ideal equal-leg fillet weld assumes the profile of an isosceles right triangle (45-45-90 degrees).
Under applied shear or tensile loads, shear failure invariably initiates across the minimum cross-sectional path extending from the root of the joint perpendicular to the weld face (hypotenuse). This shortest dimension is termed the "theoretical throat thickness":
By Euclidean trigonometry in an isosceles right triangle with equal leg lengths a:
a_throat = a * sin(45°) = a * cos(45°) = a / sqrt(2) ≈ 0.7071 * a [mm]
This establishes that the minimum load-bearing thickness is approximately 70.7 percent of the visible weld leg size.
For a continuous weld seam of effective length L, the total shear-resisting throat area is:
A_eff = a_throat * L = 0.707 * a * L [mm²]
Where L represents the net effective length after deducting start stops, cold laps, and end crater depressions.
Standard structural welding codes (AWS D1.1, AISC, and classical machine design texts such as Shigley) adopt the conservative simplification that all applied resultant forces (F), whether acting parallel or transverse to the weld axis, are resolved as pure shear stress across the throat plane:
sigma = F / A_eff = F / (0.707 * a * L) [MPa]
Where F is applied force in Newtons (N), a is leg size in millimetres (mm), and L is effective weld length in millimetres (mm).
To guarantee that the induced stress does not exceed the material allowable design limit (sigma_allow):
sigma <= sigma_allow ==> F / (0.707 * a * L) <= sigma_allow
Solving algebraically for the required leg size a:
a_req = F / (0.707 * L * sigma_allow) [mm]
This design equation provides the minimum leg dimension necessary to safely transfer the specified static load.
The following step-by-step calculation validates the tool using its factory-default input parameters:
Applying the sizing equation:
Numerator = F = 15,000 N
Denominator = 0.707 * L * sigma_allow = 0.707 * 120 mm * 140 N/mm²
Denominator = 84.84 * 140 = 11,877.6 N/mm
a_req = 15,000 / 11,877.6 = 1.26288 mm ≈ 1.26 mm
The minimum theoretical leg size required to transmit 15 kN is 1.26 mm.
a_throat = a_req * 0.707 = 1.26288 mm * 0.7071 = 0.8929 mm ≈ 0.89 mm
The theoretical throat thickness is 0.89 mm.
While theoretical statics indicates a 1.26 mm leg suffices, practical welding codes (AWS D1.1 Table 7.7 and EN 1993-1-8 Table 4.1) mandate minimum leg sizes to ensure adequate fusion and avoid rapid quenching in steel plates:
If the design engineer inputs an actual practical shop size of fillet = 4 mm:
sigma_check = 15,000 N / (0.707 * 4 mm * 120 mm) = 15,000 / 339.36 = 44.20 MPa
Because 44.20 MPa is well below the allowable limit of 140 MPa, the connection is classified as safe (safety margin n = 140 / 44.20 = 3.17).
Standard fillet welds in 90-degree corner joints form a 45-45-90 degree right isosceles triangle. The critical shear plane runs from the internal root corner perpendicular to the weld face. Trigonometrically, sin(45°) = cos(45°) = 1 / sqrt(2) ≈ 0.707106. Multiplying leg size a by 0.707 produces the exact throat dimension.
In structural steelwork designed under AWS D1.1 or AISC, allowable shear stress on the effective throat of an E70-series electrode (tensile strength 70 ksi ≈ 482 MPa) is taken as 30 percent of nominal tensile strength, yielding approximately 140 to 145 MPa. Under Eurocode 3 (EN 1993-1-8), allowable design resistance incorporates a correlation factor beta_w (0.8 to 1.0 depending on steel grade) and material partial safety factor gamma_M2 = 1.25.
No. General mechanical detailing rules specify that the leg size should not exceed the thickness of the thinner joined component (a less than or equal to t_min). Exceeding plate thickness concentrates excessive thermal energy into the joint without adding usable shear area, creating a metallurgical weak spot in the Heat-Affected Zone.
When an identical fillet weld is deposited on both sides of a T-joint, total weld length doubles (L_total = 2 · L_single). Consequently, the effective throat area is multiplied by two, halving the required leg size for a given applied static load.
Intermittent welds (such as 50 mm beads spaced at 150 mm pitch) are specified on long stiffened girders or machine covers where full continuous strength is unnecessary, saving filler metal and minimising heat distortion. However, in corrosive environments, maritime atmospheres, or pressure-tight compartments, continuous sealing welds are mandatory to prevent crevice corrosion.
a_req = F / (0.707 · L · σ_allow) | throat = 0.707 · a | τ_throat = F / (0.707 · a · L)Last updated: 2026-10-16
References
Assumptions
Guides
Browse guides with similar tags.
Engineering evaluation of load path, inspection methods, distortion, and cost when choosing fillet or full-penetration welds. AWS D1.1 and EN 1993 referenced.