DIN 931 vs DIN 933: Partial Thread vs Full Thread Hex Bolts
Understand the critical differences between DIN 931 (partially threaded) and DIN 933 (fully threaded) hex head bolts for shear and tension joints.

The Core Distinction: Unthreaded Shank vs Full-Length Thread
DIN 931 and DIN 933 are the most prevalent metric hexagon head bolt specifications in global manufacturing. The fundamental geometric distinction is straightforward:
- DIN 931 (ISO 4014): Features an unthreaded smooth shank extending from under the head, with threading applied only over a standardized portion of the nominal length.
- DIN 933 (ISO 4017): Threaded continuously right up to the underside of the hex head (full thread).
While this appears simple on paper, selecting between full-thread and partial-thread bolts significantly alters joint shear capacity, stress concentrations, alignment accuracy, and cyclic fatigue behavior.
When to Specify DIN 931 (Partial Thread)
A partially threaded bolt provides substantial advantages in structural and precision shear joints:
- Shear Plane on Solid Shank: The unthreaded body provides a larger cross-sectional area ($A = \pi d^2 / 4$) compared to the reduced thread stress area ($A_s \approx 0.78 \times A$). Bearing against a smooth shank avoids notch stress concentrations in the shear plane.
- Precision Alignment: Solid shanks prevent bolt hole play and minimize joint slip in dowelled or fitted assemblies.
- Fatigue Endurance: Thread runout situated away from the interface plane increases dynamic fatigue life under fluctuating transverse loads.
Design Constraint: The unthreaded shank length ($l - b$) must match the total clamped grip thickness. If the shank is too long, the nut bottom out against the thread runout before clamping preload is achieved.
When to Specify DIN 933 (Full Thread)
Fully threaded bolts are the standard choice for versatile assembly and general construction:
- Grip Thickness Flexibility: Ideal for maintenance, variable plate stacks, and clamping varying thickness spacers without stocking multiple bolt lengths.
- Tapped Blind Holes: Essential when threading into tapped holes where maximum thread engagement is required close to the joint surface.
- Tension-Dominated Joints: In pure axial tension (e.g., pipe flanges, pressure vessel covers), thread location relative to the interface is less critical because shear stresses are negligible.
ISO Equivalents and Drawing Callouts
In modern European and international engineering standards:
- DIN 931 corresponds closely to ISO 4014.
- DIN 933 corresponds closely to ISO 4017.
Procurement Best Practice: An engineering bill of materials (BOM) should never call out "M12 bolt" in isolation. Always specify diameter, pitch, length, standard, property class, and plating:
Hex Bolt M12 x 1.75 x 80, Grade 8.8, ISO 4014 (DIN 931), Zinc Flake ISO 10683.
Related Torqyx Engineering Tool
Verify fastener dimensions, thread pitches, and tensile stress areas across metric standards using our Fastener Database:
Fastener Database
DatabaseQuickly compare metric and imperial standard bolt dimensions, pitch, and tensile stress areas.
Related Engineering Guides
Reference Standards
- ISO 4014 / DIN 931: Hexagon head bolts — Product grades A and B (partially threaded).
- ISO 4017 / DIN 933: Hexagon head screws — Product grades A and B (fully threaded).
- ISO 898-1: Mechanical properties of fasteners made of carbon steel and alloy steel.
Related posts
What is Gear Module? Sizing and Selection Guide
Master metric gear module sizing: understand the m = d/z relationship, standard module series (ISO 54 / DIN 780), bending strength, and undercut limits.
How to Calculate Hydraulic Cylinder Force and Speed
Calculate push and pull forces for hydraulic cylinders using pressure, bore diameter, and rod diameter. Account for mechanical efficiency and buckling safety.
ISO 898-1 Fastener Standards: Property Classes and Mechanical Properties
A comprehensive engineering guide to ISO 898-1 metric bolt property classes (8.8, 10.9, 12.9), tensile and yield strength formulas, and nut matching rules.