Bolt Size & Torque
Calculate stress area and preload from nominal diameter, pitch, and grade.
Compute torsional stress and twist angle from torque and shaft size.
Enter torque, shaft geometry, and the material property.
Stress, polar moment, and elastic twist for a solid circular shaft.
Maximum shear stress τ
47.16 MPa
Twist angle θ (degrees)
1.801 deg
Safety factor based on shear stress
-
Formulas used
tau = 16T / (pi * d^3)
theta = T * L / (J * G)
J = pi * d^4 / 32
Variables
Usage notes
After checking the basic result, open sharing, PDF, method notes, and comparison panels.
Calculates torsional shear stress, polar moment, and twist angle for a circular homogeneous shaft from torque, diameter, length, and shear modulus.
Solid circular shaft check
| Input | Expected Output |
|---|---|
| T=250 N·m, d=30 mm, L=800 mm, G=80 GPa | τ≈47.16 MPa; θ≈1.801° |
Note: Evaluate the actual geometry, connection discontinuities, and combined loads separately.
Similar calculators
Explore calculators with similar categories or tags.
Calculate stress area and preload from nominal diameter, pitch, and grade.
Overview and entry point for gear design calculations.
Compute gear torque and transmitted forces.
Compute torque or power from kW, hp, and rpm.
Doc version: 1.1.0 | Updated: 2026-09-26
Enter torque, shaft geometry, and the material property.
Stress, polar moment, and elastic twist for a solid circular shaft.
Maximum shear stress τ
47.16 MPa
Twist angle θ (degrees)
1.801 deg
Safety factor based on shear stress
-
Formulas used
tau = 16T / (pi * d^3)
theta = T * L / (J * G)
J = pi * d^4 / 32
Variables
Usage notes
After checking the basic result, open sharing, PDF, method notes, and comparison panels.
When a circular shaft transmits a torque, the cross-section rotates relative to an adjacent cross-section. The resulting shear strain varies linearly from zero at the neutral axis to a maximum at the outer surface, allowing a closed-form analytical solution.
Assuming plane sections remain plane and circular sections remain circular (valid for homogeneous, isotropic elastic material), the shear strain at radius r from the centroidal axis is:
gamma(r) = r * (d_theta / dz) [rad]
Combining with Hooke's law for shear (tau = G * gamma):
tau(r) = G * r * phi / L
Equilibrium requires the resultant moment of internal shear forces to equal the applied torque T:
T = integral[ r * tau(r) dA ] = (G * phi / L) * integral[ r^2 dA ] = G * J * phi / L
For a solid circular cross-section, the polar second moment of area is:
J = pi * d^4 / 32 [mm^4]
Shear stress reaches its maximum at the outermost fibre (r = d/2):
tau_max = T * c / J = 16 * T / (pi * d^3) [MPa]
Here c = d/2 is the outer radius, T is in N·mm, d in mm, so tau_max is obtained directly in MPa.
Re-arranging T = G * J * phi / L to isolate the angle of twist phi:
phi = T * L / (J * G) [radians]
Convert to degrees for engineering reporting:
phi_deg = phi * (180 / pi)
The allowable shear stress (tau_allow) is obtained from the material specification or design standard. The static safety ratio is:
n = tau_allow / tau_max
If n is greater than 1.0 the design is acceptable; if n is less than 1.0 the shaft diameter must be increased or the material upgraded.
Step-by-step numerical verification using the calculator's factory default values:
J = pi * 30^4 / 32 = pi * 810,000 / 32 = pi * 25,312.5 = 79,521.6 mm^4
Polar second moment of area: J = 79,521.6 mm⁴.
tau_max = 16 * 250,000 / (pi * 30^3)
= 4,000,000 / (pi * 27,000)
= 4,000,000 / 84,823
= 47.16 MPa
Peak surface shear stress: tau_max = 47.16 MPa.
phi = (250,000 * 800) / (79,521.6 * 80,000)
= 200,000,000 / 6,361,728,000
= 0.03144 radians
Converting to degrees:
phi_deg = 0.03144 * (180 / pi) = 0.03144 * 57.296 = 1.801 degrees
Angle of twist: 1.801 degrees.
n = tau_allow / tau_max = 80 / 47.16 = 1.70
Safety ratio n = 1.70 — the shaft is adequate for static shear loading (n is greater than 1.0).
A commonly cited rule of thumb for general-purpose transmission shafts is 0.5 to 1.5 degrees per metre of shaft length, with up to 3 degrees per metre tolerated in some automotive driveshaft applications. In this example the twist rate is 1.801° over 0.8 m, equivalent to 2.25°/m, which approaches the upper end of the typical range and may warrant review if precise angular positioning is required.
For static loading, ASME B106.1M recommends tau_allow = 0.3 × yield strength in tension or 0.18 × ultimate tensile strength (whichever is smaller). For fatigue loading, the corrected endurance limit in shear is calculated using the Shigley method, which accounts for surface finish, size, reliability, and load-type modifying factors.
A hollow shaft delivers a significantly higher specific torsional stiffness (torque capacity per unit mass) than a solid shaft of the same outer diameter. The polar moment of area falls only slightly as the core is removed, while the mass reduction is proportional to the square of the bore-to-outer diameter ratio. This is why aerospace, motorsport, and marine driveshafts routinely use hollow titanium or aluminium sections.
Measured deflection can exceed the theoretical prediction for several reasons: bearing clearances and coupling compliance add extra rotation that is not captured by the shaft-only formula; the actual shear modulus of a given heat of steel may differ from the nominal 80 GPa; and surface friction in spline interfaces can redistribute torsional compliance along the drivetrain.
For static loading with well-characterised loads, a safety ratio n greater than 1.5 is the generally accepted minimum. For shock or dynamic loading, n greater than 2.0 is recommended. In this example n = 1.70 is satisfactory for static duty but should be revisited if the application involves start-up shock torque peaks significantly above the rated value.
Calculates torsional shear stress, polar moment, and twist angle for a circular homogeneous shaft from torque, diameter, length, and shear modulus.
Solid circular shaft check
| Input | Expected Output |
|---|---|
| T=250 N·m, d=30 mm, L=800 mm, G=80 GPa | τ≈47.16 MPa; θ≈1.801° |
Note: Evaluate the actual geometry, connection discontinuities, and combined loads separately.
J = pi d^4 / 32 | tau_max = 16 T / (pi d^3) | theta = T L / (J G)Last updated: 2026-09-26
References
Assumptions
Guides
Browse guides with similar tags.
DIN 6885 shaft-hub parallel keys, shear and bearing crushing stress verification, wedge mechanics, and self-locking conditions.
High-cycle fatigue analysis, S-N Wöhler curves, Marin modification factors, Goodman failure criterion, and Miner cumulative damage rule.